Configuration — Abbas Dominus3 Security System¶

Everything you can add with this adapter: where it goes in the tree, what you fill in, and what you can tell it to do.

Dominus3 Panel¶

Abbas Dominus3 central control unit


Add it under	nothing — this is the top of the tree
Identified by	nothing — there is only one
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
ip_address	yes	—	host name or IP address	Panel host or IP address
connection_name	yes	—	text	Connection identity (configured in SetDom)
connection_password	yes	—	text	Connection pre-shared key (configured in SetDom) (stored as a secret)

Subsystem¶

Alarm subsystem (partition) with independent arm/disarm state


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	an access point people pass through

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Subsystem ID from panel

What you can command it to do¶

Command	What happens
Arm	Arm security monitoring
Disarm	Disarm security monitoring

Concentrator¶

CTR bus concentrator module


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	CTR module ID from panel

Detector¶

Intrusion detector or sensor on CTR bus


Add it under	Concentrator (up to 255), Access Module (up to 255), Keypad (up to 255)
Identified by	the address you fill in below
Role	—

What it must be linked to¶

Setting	Link to	Required	What it is for
partitions	Subsystem (one or more)	optional	Subsystems this detector belongs to; configure from Dominus detector-to-subsystem mapping

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Detector ID from panel

What you can command it to do¶

Command	What happens
Bypass	Temporarily exclude from monitoring
Cancel Bypass	Cancel bypass and resume monitoring

Keypad¶

KPD keypad module


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	KPD module ID from panel

Power Supply¶

Power supply module with mains and battery supervision


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Power supply module ID from panel

Sargos Distress Module¶

Sargos distress module carrying the panic buttons of one area


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What it must be linked to¶

Setting	Link to	Required	What it is for
partitions	Subsystem (one or more)	optional	Subsystems this distress module belongs to; the panel does not report this, so enter it from the site's module-to-subsystem list

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Sargos module ID from panel

Relay Output¶

Controllable relay output


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Output ID from panel

What you can command it to do¶

Command	What happens
Activate	Activate output relay or control point
Deactivate	Deactivate output relay or control point

Access Module¶

ACC access control module


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	—

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	ACC module ID from panel

Channel¶

Wiegand reader channel on ACC module


Add it under	Access Module (up to 2)
Identified by	the address you fill in below
Role	counts towards anti-passback

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Channel ID from panel

Access Door¶

Logical access control door


Add it under	Dominus3 Panel (up to 255)
Identified by	the address you fill in below
Role	an access point people pass through

What it must be linked to¶

Setting	Link to	Required	What it is for
entry_reader	Channel	optional	Entry side reader channel
exit_reader	Channel	optional	Exit side reader channel
door_contact	Detector	optional	Detector used as door contact sensor

What you fill in¶

Setting	Required	Default	Accepted values	What it does
address	yes	—	1–9999	Door ID from panel

What you can command it to do¶

Command	What happens
Open	Open door momentarily (unsecure strike temporarily)
Open Permanent	Hold door unsecured indefinitely (extended access mode)
Close	Close a permanently opened door - return to normal operation
Lock	Lock door - deny entry, cards included, until unlocked
Unlock	Unlock door - return to normal operation, cards decide